Welcome to UK420

Register now to gain access to all of our features. Once registered and logged in, you will be able to contribute to this site by submitting your own content or replying to existing content. You'll be able to customize your profile, receive reputation points as a reward for submitting content, while also communicating with other members via your own private inbox, plus much more!

This message will be removed once you have signed in.


Sign in to follow this  
Followers 0
LANKY SI

my small canvas

Hi all as mentioned in my introduction I am going to be using a small shower room that as never been fully converted

r1rs

once I have tidied it up a little starting tomorrow and sorted the cctv plus removed the lower shelves I will be putting a budbox in there 1 x 1 x 1.8 this will leave me around 50mm gap around the sides for airflow and also a few hundred above
Edited by LANKY SI
4 people like this

Share this post


Link to post

Very nice mate.

Is that a tv/monitor in there?

Also, my eyes seem to have reverted to a 1950s format. Is that a B&W pic or am I really back in the 50s? lol

Share this post


Link to post

Very nice mate.

Is that a tv/monitor in there?

Also, my eyes seem to have reverted to a 1950s format. Is that a B&W pic or am I really back in the 50s? lol

hahaha too much bud :D yeah hit the grayscale when converted the size ..... the monitor is for the cctv ;)

1 person likes this

Share this post


Link to post

hahaha too much bud :D yeah hit the grayscale when converted the size ..... the monitor is for the cctv ;)

That's dead fucking posh mate lol

Nice one :)

Share this post


Link to post

It wont look like that tomoz ... going to work some magic hopefully have a few of hours at it :D

Share this post


Link to post

:)

Share this post


Link to post

good luck as i use a budbox 1.8 myself, it'll be a bugger trying to put it up in the cupboard but it is possible.

Share this post


Link to post

good luck as i use a budbox 1.8 myself, it'll be a bugger trying to put it up in the cupboard but it is possible.

you were not kidding :D the last bar was a bugger should have took the shelves I left higher I had to install the extractor first otherwise the tent would have been in the way I have around 150mm at the back and 50 each side above there is plenty

uggh its in hahaha

I only plan on doing one or two CACTI max at a time due to the space and the learning curve ahead

I am stood now though awaiting some spare coin for some led lighting :)

Edited by LANKY SI
3 people like this

Share this post


Link to post

save your spare coin & ditch the LEDS, what you want for that space is a 315w CMH light, you should check out the lighting section as theres a detailed thread on CMH lighting for more info :yes:

5 people like this

Share this post


Link to post

save your spare coin & ditch the LEDS, what you want for that space is a 315w CMH light, you should check out the lighting section as theres a detailed thread on CMH lighting for more info :yes:

thanks will do ... first impression they are expensive however only got to page 10 on the thread so far ... might try a led first to tick me over until I can afford cmh I will keep reading though and thanks for the info

Share this post


Link to post

the cheapest reputable kit so far if you shop around is a 315w maxibright ballast at £150, £64 for a 942 lamp, £64 for the 930, £90 for a 930 agro (best for flowering)

£18 for a E40-CMH adaptor & £20 for a euro reflector, probably cost you in the region of £250 & £280'ish ;)

even tho i don't keep track of the price of Led lights, i do know a good light unit is expensive to buy & if you compare the specs between Leds v CMH, even HPS & MH, they all out perform Leds.

2 people like this

Share this post


Link to post

the cheapest reputable kit so far if you shop around is a 315w maxibright ballast at £150, £64 for a 942 lamp, £64 for the 930, £90 for a 930 agro (best for flowering)

£18 for a E40-CMH adaptor & £20 for a euro reflector, probably cost you in the region of £250 & £280'ish ;)

even tho i don't keep track of the price of Led lights, i do know a good light unit is expensive to buy & if you compare the specs between Leds v CMH, even HPS & MH, they all out perform Leds.

is this the ballast you mean Hogger ?

light

Edited by LANKY SI

Share this post


Link to post

no, that one in the pic is the mk1 version, the new mk2 is a good bit smaller.

315w-maxibright-daylight-cdm--f60.jpg

1 person likes this

Share this post


Link to post

looks good friend, best of luck

Share this post


Link to post

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!


Register a new account

Sign in

Already have an account? Sign in here.


Sign In Now
Sign in to follow this  
Followers 0