Register now to gain access to all of our features. Once registered and logged in, you will be able to contribute to this site by submitting your own content or replying to existing content. You'll be able to customize your profile, receive reputation points as a reward for submitting content, while also communicating with other members via your own private inbox, plus much more!
This message will be removed once you have signed in.
Search the Community: Showing results for tags 'SAFE'.
Found 2 results
Hi all, first of all I have to say how brilliant this community is! So much useful info all in one place. So I am very close to starting the process of creating medicine for my nephew who has been diagnosed with cancer for the third time, this time in his neck, stomach and chest. He has had chemo each time and has beaten it but this time it has come back worse hence turning to cannabis medication.I have done endless research on the different ways to create the extract and it seems like every way has its own risks involved so after much consideration I have decided on the method below and just want to run it by the experts before I get going.So here we go...... 1) lightly grind and decarb the bud in the oven between sheets of grease proof paper (will double check times and duration before hand) 2) Leave to cool and grind to dust3) load dust into extraction tube using coffee filters over the open end secured with tape/rubber bands? (Any more secure method anyone could suggest?)4) blast the product using DEXSO - DIMETHYL ETHER near zero impurities into a Pyrex tray(This is one of the main things I would like advice on, does anyone know much about this product? I’ve looked into it as much as I can and sounds as though it would be a much healthier option than butane, it’s even used to collect natural oils in certain food preperation)5) soon as the oil/dexso mix stops dripping from the extractor, move the Pyrex tray to a hot water bath for the mix to evaporate until it stops bubbling6) collect the oil with razor blades on to grease proof paper spreading it thin and even(the nice and messy bit!)7) place collected oil on the g/p paper into a vacuum chamber 8) place chamber on a gentle heating device and turn on vacuum pump. (Not sure what to use yet as the heating device but I have my laser gun thermometer ready to make sure the oil doesn’t get to hot)(Should have mentioned that I have made oil (BHO) before but not for medical use hence the extra precautions this time round. I’ve always purged only using heat before so from the vacuum chamber onwards it’s all new to me)9) oil will bubble and expand which I plan on just judging by eye when to stop the pump, letting the oil decrease in size, popping the large bubbles with the tip of a razor and repeating until I am happy that I have got out every impurity that I can.10) place final product in fridge to solidify (I am hoping for something close to the consistency of shatter when cooled so that I can snap and weigh easily, if the final product is too soft I will most likely opt for empty capsules to easily control dosage)11) weigh out doses that will also be left in the fridge12) take doses as you would a tablet with ice cold water so the oil doesn’t start to liquify until it’s in the stomachAny advice from anyone that has solid knowledge would be much appreciated, especially on the solvent (dexso) that I plan on using and anything else that I could improve to create as clean of a product as possible.Thank you for reading.
Looking for some help in regards to vaping to get CBD OK so i have a health condition (Chrohns) i find high CBD weed really effective. At the moment I'm smoking joints i also smoke tobacco i also have access to an Arizer extreme Q . I want to give up using tobacco completely for obvious reasons, My only prior experience is using the Arizer desktop vape , which to be honest i personally haven't found as effective as smoking, so here is my main concern In order to get the CBD to become active i believe the temp has to quiet that bit higher then to get THC off from what i remember CBD doesn't come off till around 200c is 200c also the starting point of combustion ? there for negating any real health benefits ?....... (I'm hoping this is wrong ) I'm asking because i would like to give vaping another go ,id like to purchase a portable vape ideally one that does dry herb dont want to mess with Butane and i have 0% faith in off the shelf CBD oil Another issue i had with desktop vape is because i was starting off at high temp 210c it took any taste of the weed out, i suspect because terpenes burn off at a much lower temp ? I have since read in specific in relation extreme Q that i may have not been using it properly in respect that i didn't let it potentially heat up enough before using i tended to put herb in put at desired temp usually between 200 -230c leave from a min and turn fan on , i've read its best let it heat up for up 10 min before turning fan on , so I'm in the process of trying that (having to order replacement bags) I like the idea of getting portable dry herb chamber vape to help give up smoking but obviously i want that to be of some benefit to health and depending on what i find out about it will influence my decision weather to bother investing more in vaping or find another way ? .