LANKY SI Posted April 1, 2016 Share Posted April 1, 2016 (edited) Hi all as mentioned in my introduction I am going to be using a small shower room that as never been fully converted once I have tidied it up a little starting tomorrow and sorted the cctv plus removed the lower shelves I will be putting a budbox in there 1 x 1 x 1.8 this will leave me around 50mm gap around the sides for airflow and also a few hundred above Edited April 1, 2016 by LANKY SI 4 Link to comment Share on other sites More sharing options...
Twisted Rizla Posted April 1, 2016 Share Posted April 1, 2016 Very nice mate. Is that a tv/monitor in there? Also, my eyes seem to have reverted to a 1950s format. Is that a B&W pic or am I really back in the 50s? Link to comment Share on other sites More sharing options...
LANKY SI Posted April 1, 2016 Author Share Posted April 1, 2016 Very nice mate. Is that a tv/monitor in there? Also, my eyes seem to have reverted to a 1950s format. Is that a B&W pic or am I really back in the 50s? hahaha too much bud yeah hit the grayscale when converted the size ..... the monitor is for the cctv 1 Link to comment Share on other sites More sharing options...
Twisted Rizla Posted April 1, 2016 Share Posted April 1, 2016 hahaha too much bud yeah hit the grayscale when converted the size ..... the monitor is for the cctv That's dead fucking posh mate Nice one Link to comment Share on other sites More sharing options...
LANKY SI Posted April 1, 2016 Author Share Posted April 1, 2016 It wont look like that tomoz ... going to work some magic hopefully have a few of hours at it Link to comment Share on other sites More sharing options...
Twisted Rizla Posted April 1, 2016 Share Posted April 1, 2016 Link to comment Share on other sites More sharing options...
Joint hogger Posted April 2, 2016 Share Posted April 2, 2016 good luck as i use a budbox 1.8 myself, it'll be a bugger trying to put it up in the cupboard but it is possible. Link to comment Share on other sites More sharing options...
LANKY SI Posted April 2, 2016 Author Share Posted April 2, 2016 (edited) good luck as i use a budbox 1.8 myself, it'll be a bugger trying to put it up in the cupboard but it is possible. you were not kidding the last bar was a bugger should have took the shelves I left higher I had to install the extractor first otherwise the tent would have been in the way I have around 150mm at the back and 50 each side above there is plenty I only plan on doing one or two CACTI max at a time due to the space and the learning curve ahead I am stood now though awaiting some spare coin for some led lighting Edited April 2, 2016 by LANKY SI 3 Link to comment Share on other sites More sharing options...
Joint hogger Posted April 2, 2016 Share Posted April 2, 2016 save your spare coin & ditch the LEDS, what you want for that space is a 315w CMH light, you should check out the lighting section as theres a detailed thread on CMH lighting for more info 4 Link to comment Share on other sites More sharing options...
LANKY SI Posted April 4, 2016 Author Share Posted April 4, 2016 save your spare coin & ditch the LEDS, what you want for that space is a 315w CMH light, you should check out the lighting section as theres a detailed thread on CMH lighting for more info thanks will do ... first impression they are expensive however only got to page 10 on the thread so far ... might try a led first to tick me over until I can afford cmh I will keep reading though and thanks for the info Link to comment Share on other sites More sharing options...
Joint hogger Posted April 5, 2016 Share Posted April 5, 2016 the cheapest reputable kit so far if you shop around is a 315w maxibright ballast at £150, £64 for a 942 lamp, £64 for the 930, £90 for a 930 agro (best for flowering) £18 for a E40-CMH adaptor & £20 for a euro reflector, probably cost you in the region of £250 & £280'ish even tho i don't keep track of the price of Led lights, i do know a good light unit is expensive to buy & if you compare the specs between Leds v CMH, even HPS & MH, they all out perform Leds. 2 Link to comment Share on other sites More sharing options...
LANKY SI Posted April 6, 2016 Author Share Posted April 6, 2016 (edited) the cheapest reputable kit so far if you shop around is a 315w maxibright ballast at £150, £64 for a 942 lamp, £64 for the 930, £90 for a 930 agro (best for flowering) £18 for a E40-CMH adaptor & £20 for a euro reflector, probably cost you in the region of £250 & £280'ish even tho i don't keep track of the price of Led lights, i do know a good light unit is expensive to buy & if you compare the specs between Leds v CMH, even HPS & MH, they all out perform Leds. is this the ballast you mean Hogger ? Edited April 6, 2016 by LANKY SI Link to comment Share on other sites More sharing options...
Joint hogger Posted April 6, 2016 Share Posted April 6, 2016 no, that one in the pic is the mk1 version, the new mk2 is a good bit smaller. 1 Link to comment Share on other sites More sharing options...
JeezaK Posted August 13, 2016 Share Posted August 13, 2016 looks good friend, best of luck Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now