UK420: 80cm Parabolic reflector - UK420

Jump to content

     

  • 2 Pages +
  • 1
  • 2
  • You cannot start a new topic
  • You cannot reply to this topic

80cm Parabolic reflector Where's the instruction manual??!! Rate Topic: -----

#1 _budzilla2010_

  • Group: Guests
  • Member No.:

Posted 06 January 2011 - 12:32 PM

Hey Guys,

The new Para's just arrived. one problem, seems to be no instructions with it. :spliff:

Can anyone give me a hand??

I assume the triangle shaped plated need to be layered like a fan but do i bolt them in so they are underneath the top octagon or do i bolt them to the top of the octagon??

Also i assumed screw head to be on the reflective side and nut to be on the outer (non reflective side)??

any help would be awesome, asap please!!! i really wannna get it in now!!!

Cheers


...BudZ...
0

#2 _budzilla2010_

  • Group: Guests
  • Member No.:

Posted 06 January 2011 - 12:39 PM

Also, this octagon thing at the top with teh vents in, should the vents be pointed up and out of teh hood, so its flat on teh reflective side?
0

#3 User is offline   Justanotherbloke 

  • Vegging Nicely
  • PipPipPip
  • Group: Full Member
  • Member No.: 57199
  • Posts: 494
  • Joined: 30-July 10

Posted 06 January 2011 - 12:53 PM

The louvres on the top of the octagon, the plates overlapping and bolted on top of the octagon, with the nuts to the top.

Hope that helps.

Bloke
1

#4 _budzilla2010_

  • Group: Guests
  • Member No.:

Posted 06 January 2011 - 12:56 PM

Louvres on the top so the bottom is flat and the top is raised yeah??

Did you have to bend your wings where it meets at the top to get it to fit?

Cheers,

...BudZ...
0

#5 User is offline   Justanotherbloke 

  • Vegging Nicely
  • PipPipPip
  • Group: Full Member
  • Member No.: 57199
  • Posts: 494
  • Joined: 30-July 10

Posted 06 January 2011 - 01:02 PM

Yes the bottom is flat.

The easiest way to fit the wings IMO is to connect the two fixings at the top on all of the wings to the octoagon first, then connect the next row down of fixings and so on. It can be a bit tricky and you have to flex the wings to connect the fixings on the bottom row.

Hope that helps

Bloke

This post has been edited by Owderb: 06 January 2011 - 02:02 PM

0

#6 _budzilla2010_

  • Group: Guests
  • Member No.:

Posted 06 January 2011 - 01:04 PM

Yes cool, thats been much help thanks.

One last point. so did you tighten up the top screws that bolt onto teh octagon thingy fully tight, then work your way down bending as necesary or did you have it loose to start with and tighten up after all teh bolts are on??

I was thinking tighten up fully then work my way down, just wanted to clarify that before i proceed?

cheers
0

#7 User is offline   Justanotherbloke 

  • Vegging Nicely
  • PipPipPip
  • Group: Full Member
  • Member No.: 57199
  • Posts: 494
  • Joined: 30-July 10

Posted 06 January 2011 - 01:10 PM

Pm me your address and I will come round and build it for you....just give us a fiver plus travel expenses :soap:

Only kidding, just tighten the nuts up finger tight as you go, then if required you can "nip" them up tight when it's built.

Good choice of reflector too I reckon.


Bloke
0

#8 User is offline   playingedges 

  • DAGGA
  • PipPipPipPip
  • Group: Full Member
  • Member No.: 29210
  • Posts: 551
  • Joined: 21-January 08

Posted 06 January 2011 - 01:11 PM

View Postbudzilla2010, on Jan 6 2011, 01:33 PM, said:

Yes cool, thats been much help thanks.

One last point. so did you tighten up the top screws that bolt onto teh octagon thingy fully tight, then work your way down bending as necesary or did you have it loose to start with and tighten up after all teh bolts are on??

I was thinking tighten up fully then work my way down, just wanted to clarify that before i proceed?

cheers


I had to do this a couple weeks back - see my grow diary for a photo of it complete.

I tightened them up fully before proceeding to the next screw. Also, I fastened the 'fan' pieces to the octagon place first, then I did the outer ring before moving to the middle ring.

And don't be shy - you need to bend those fan pieces like a mo'fo :soap:

PE
"Criminalising young people doesn't make drugs safer. Throwing heroin users in prison doesn't treat their addiction. Banning the latest 'legal high' doesn't stop kids trying the next one. Pretending that you're winning the war, doesn't mean that you are."
-- Release

First grow. First diary. 400W HPS. Soil.
0

#9 _budzilla2010_

  • Group: Guests
  • Member No.:

Posted 06 January 2011 - 02:07 PM

Done it!! 1hr 30 mins!! is that a world record??

Thanks very much for teh help guys. my hands are hurting now.

just incase anyone else is doing the same and reading this. I found starting at the top and getting all the bolts into teh octagon fully tight them moving to teh middle ones was fine. quite easy to allign the holes if you have teh whole thing resting in your lap so you can curve it.

I also noticed that a lot of the bolts wont quite match up to the holes. If you get it so its resting in the hole but wont go through turn the screw with the screwdriver and it will make its way through to teh other side, pop the nut on and tighten fully.

i tightened every nut fully before moving onto the next. top, then middle, then finaly the bottom.

its a peice of piss when you know where to start, is a bit fiddly but if your any good with Mechano then this should be a doddle!! You just need to knwo where to start off.


Cheers for all teh help dudes,


...BudZ...
0

#10 User is offline   Joint hogger 

  • Resin Coated
  • PipPipPipPipPipPip
  • View gallery
  • Group: Senior Member
  • Member No.: 36349
  • Posts: 3193
  • Joined: 20-September 08

Posted 06 January 2011 - 05:06 PM

start with the top bolt, leaving them loose, then loosely bolt the bottom bit then the middle, once they're all in, tighten them up.

i found it easier doing it this way after putting 3 together for other folk, luckily i was meccano mad when i was younger :naughty:
Basic single Variac build - Modded Basic Variac - twin Variac build - Veg Cab - Variacs Transformers
2

#11 _budzilla2010_

  • Group: Guests
  • Member No.:

Posted 06 January 2011 - 05:16 PM

Cheers dude! :naughty: i finished building it 4 hours ago though!! Your way probably stops bits from bending, I'm getting some more for the 600's. So will try your way then

cheers anyway Chop Chop (''bit early in the morning for Kung-foo init Jim?'')

:wink:

...BudZ...
0

#12 User is offline   organicuk 

  • Vegging Nicely
  • PipPipPip
  • View gallery
  • Group: Full Member
  • Member No.: 17644
  • Posts: 495
  • Joined: 02-November 06

Posted 06 January 2011 - 05:31 PM

omg that would proper stress me out that. haha let me know how it is,

am thinkin of getting one for the summer , because i dont think my room will able to cope with the 2 6's

whats the smallest size they do these in ?
i need the oil , oil , oil is what i need and if i share with you my story will you share your oil with mee
__________________________________________________________________________________
NYC Diesel 20 Plant
Click Here NYCD
0

#13 User is offline   playingedges 

  • DAGGA
  • PipPipPipPip
  • Group: Full Member
  • Member No.: 29210
  • Posts: 551
  • Joined: 21-January 08

Posted 06 January 2011 - 05:38 PM

View Posthydroponicuk, on Jan 6 2011, 06:00 PM, said:

omg that would proper stress me out that. haha let me know how it is,

am thinkin of getting one for the summer , because i dont think my room will able to cope with the 2 6's

whats the smallest size they do these in ?


80cm is the smallest mate.

PE
"Criminalising young people doesn't make drugs safer. Throwing heroin users in prison doesn't treat their addiction. Banning the latest 'legal high' doesn't stop kids trying the next one. Pretending that you're winning the war, doesn't mean that you are."
-- Release

First grow. First diary. 400W HPS. Soil.
0

#14 User is offline   organicuk 

  • Vegging Nicely
  • PipPipPip
  • View gallery
  • Group: Full Member
  • Member No.: 17644
  • Posts: 495
  • Joined: 02-November 06

Posted 06 January 2011 - 06:05 PM

cheers man
i need the oil , oil , oil is what i need and if i share with you my story will you share your oil with mee
__________________________________________________________________________________
NYC Diesel 20 Plant
Click Here NYCD
0

#15 _budzilla2010_

  • Group: Guests
  • Member No.:

Posted 07 January 2011 - 02:10 AM

The light spreads 5 X better than the diamond. Get one!
0
  • 2 Pages +
  • 1
  • 2
  • You cannot start a new topic
  • You cannot reply to this topic

1 User(s) are reading this topic
0 members, 1 guests, 0 anonymous users


 

Warning: It is an offence in most countries to cultivate any plant of the genus Cannabis without a license from the relevant authorities.
Anyone committing an offence contrary to their local laws may be imprisoned, fined or both. Visitors are advised against breaking the law. We advise you to make yourself aware of the relevant laws in your own country.
All information contained on this website is for educational and entertainment purposes only and is not intended to condone, promote or incite the use of illegal or controlled substances.
Neither UK420.com or any member of its staff of volunteers can accept responsibility for unsolicited manuscripts or photographs submitted to it. You must be aged 18 or over to view this website.