Register now to gain access to all of our features. Once registered and logged in, you will be able to contribute to this site by submitting your own content or replying to existing content. You'll be able to customize your profile, receive reputation points as a reward for submitting content, while also communicating with other members via your own private inbox, plus much more!
This message will be removed once you have signed in.
Search the Community: Showing results for tags 'boobies'.
Found 4 results
badbillybob posted a topic in Humboldt Seed Organisations 2020 Outdoor Grow DiariesHello hello, my fresh faced outdoor naturalists (or naturists- whatever floats your boat, but watch out for the ticks) First up for this years diaries and im in. The eagle has landed, in the form of an envelope from Spain These are going outdoors in a couple of months and I shall pray for a long hot summer. Im at latitude 57, just shy of the arctic circle lol. I am using the same plots as last year, but im thinking about topping up the soil holes with some new stuff, cos I need the exercise. I will update once ive managed to get out there and check the sites, with a couple of pics. One of my sites is a bit flooded, in one area, it was the same last year, so im gonna avoid that part and dig some more holes. Should be good, buckle up for some mad adventures.
Hello there everyone. ive been growing out Dinafem beans since i started growing, and honestly, can hand on heart tell you that ive yet to be dissapointed in any of the strains that i have done. Just lately my growing has been going off a bit, lost my mojo, gone a bit stale, ive not been as enthusiastic as usual about my favourite hobby, and have had more than my fair share of dissasters...just have a look at my outdoor threads, or my breeding fiascos, as usual. So ive decided that what i need is a challenge......... a real challenge............ a real big challenge.........real BIG Soooooo, ive decided that for my next grow, im going to try and beat my previous personal best, and im gonna try and get ONE KILO of dried buds,.............. from a single plant........ Yes, you heard it first here, ......the kilo challenge is on...ive said it now, so i better make it happen. my previous personal best was 760 grams from one, but this time we are going big or going home. Growing huge plants indoors isnt as straight forward as just veging them for ages and letting rip, these will be dependant on timings for everything, toppings, lighting and nutrient schedules and environment need to absolutely bang on. Any mistakes can prove costly... The strain choice is Dinafems BIG Kush, a strain which ive grown previously , which surprised me in just how massive it got, and how good the bud was from it (the two are normally not exclusive). Every one of my mates who smoked it agreed that it was a belter, and it improved massively after a good cure. Dinafem Mark has very generously agreed to front the beans for this adventure, and im going to try my damnedest to make the KILO happen. its been a long standing ambition of mine, just to see if i could do it...fingers crossed etc we will be popping the beans as soon as they land and vegging for about 10 weeds in the rdwc. i tell you now, this is gonna be EPIC....there will be more info in the diary, so keep yer eyes peeled for the diary starting Go BIG or go home, as Guy Martin would say.... Trees for life, as i would say
Hello, my fellow herb enthusiasts, I have decided to put up a short build guide for people considering RDWC. Now I have pictured 2 of my previous system builds, but unfortunately, the pigs stole them so I'm a bit limited in showing actual photos of various parts of the build. I have built quite a few of these over the years, each one has been a learning process, and not without disaster along the way, as u do. The systems shown will fit in a 2.4 by 1.2 tent (the 4 pot one) or a 1.2 tent (the 2 pot one) These are NOT undercurrent systems, they are simple recirculating systems, utilising 22mm spray bars for the delivery and 40mm returns to the res. I have located the res outside of the tent in both systems, because this helps keep the temperature of the nutrients cooler, and reduces the work for the chiller (i'll come to that later) So the system works by the process of pumping nutrient around the system, through the spray bars. This nutrient solution is highly oxygenated, with high levels of dissolved oxygen produced by the falling water disturbing the surface tension (which creates DO(dissolved oxygen). Now I'm not saying that this system is perfect or cant be improved upon, because nothing is perfect is it, its all a compromise in some way or other, before you all start slagging it off and telling me how I should have done this or that or whatever. I'm not really interested, ok? good.......... then we shall proceed Lets start with a list of stuff you will need to complete this build (2 pot system) The pictures are meant as a guide only as some of the stuff I describe is what I would do differently if I was to do it again 3No. really useful boxes (2 for the plants , one for the res) either 64 or 84 litre jobs (the more nutrient you have the more stable the EC and Ph will remain). this is why I use big boxes A hole cutter for 22mm and 40mm pipework. A number of 40 mm tank connectors (6 in this case), plus 40mm pipework, bends and tees to suit. I use solvent weld fittings, which do not leak if done properly, unlike the push fit ones. The solvent weld fittings are also cheaper woop woop. the down side is that if you ever want to move the system or dismantle it, you will need a hacksaw lol. A number of 22mm pipework fittings including bends, tees and pipework. I am not stating how many of each you use because it will depend on how you lay it out. I'm sure you are capable of working this part out for yourselves A water pump _ I would recommend a 4000l/hr one for this size system, the 4 pot system I used a 6000l/hr one, but should have gone bigger. A reducer from the water pump outlet to the 22mm spray bar. These can be bought off ebay as silicone reducers , just pump in the sizes, e.g 22mm to 26mmm or whatever it is. Stainless hose clamps to suit this reducer, both ends. various drill bits, a drill, A chiller- will depend on the total capacity of your system, for a 2 pot system I reckon you would be ok with a 150l chiller, I used a 300l one on the 4 pot system Maxijet 1000l/hr pump and hose to suit the chiller. Right, now to the construction part. we will start with the returns. these are 40mm, which are a decent compromise, you can go bigger (but they are expensive) or smaller (more likely to block with roots etc) So take your really useful boxes and lay them in the tent where you want them to go, this is how I did it As you can see the totes are side by side with the return pipes at the front and back of each box. Its always a good idea to set things out to make sure there is enough room for like lids to fit on (ahem), and all the pipework to fit etc. Now once you know where its all going measure out your pipes, notiing where each one goes. I lay them out on the floor the way they will go in the tent, makes life a little easier. The return pipes are attached to the box via the 40mm tank connector, which is solvent welded to the pipe When you drill the hole for the tank connector/ bulkhead, you want to try and get it very close to the bottom of the box,, BUT make sure you still have room to screw on the nut. When you get the tank connectors you will see a rubber washer type thing - this goes to the outside of the box ok? A word on solvent cement- you can get high as fuck off it so use in a well ventilated area (that's the health and safety pish out the way) Also, when using solvent cement, this is what I do to prevent bailing water out of the tent/ leaks . Saw cut the end of the pipe, then sand off the rough end where all the scrappy bits are, and a small chamfer on the end of the pipe. (Use 100 grit sandpaper or above) Make sure nothing is sticking out from the pipe, like rough edges etc Put the solvent cement on the end of the pipe, AND on the inside of the fitting it is getting connected to. Now stick em together, you don't get long. When I join them together I kinda push the pipe in and give it a 1/4 turn at the same time. wipe off the excess glue (don't put it back in the glue pot) Leave this for 15 minutes and it will be solid. So glue all the returns together, putting it in the box, measuring trimming etc as you go, to be sure it will all FIT properly. No point glueing it all together then finding out your 10mm out on a measurement has fucked half of it up is there. The returns are at opposite sides of the really useful box to equalise the return flow, so that the roots stay in the centre of the box. If both returns were at the same side of the box, the roots WILL migrate there and clog the returns. In the picture above you will see just below the spray bar Tee, the return pipes go to a tee fitting and then back to the res. If I was to do it again I would have 2 returns to the res, just in case the one was to block with root (unlikely tho it may be). The picture above also shows the spray bars, the 22mm pipe inside the box which delivers the nutrients to the tote. Drill the holes for these as high up the sides of the box as possible, you want as much fall from the water as possible. This one is drilled just below the top lip. These are done in a similar fashion to the returns, but it is easier to drill the holes for the nutrient to spray from before you glue the lot together. I use a small drill bit for the holes, and for this system, if I remember I had something like 4 holes on each long side and 2 on the short sides. I had these holes drilled in such a way to spray the water around the base of the net pot, about an inch or 2 away from the actual pot itself, but its not really critical where the holes go, as long as the water can splash on the surface, creating DO. The spray bars go to a TEE which goes to a single pipe from the water pump. A word of advice - the pump outlet has a reducer attached, and then it goes to the 22mm pipe. You will see that this pipe goes through the side of the res. there is a reason for this, which is - if somehow the pipe detaches from the reducer, it will not go flying out of the way allowing the fountain from the res to flood the room, as the side hole will keep the pipe in place. See pic below. Again if I was doing this again I would have the pump closer to the tent side of the box. this pic also shows the reserviour, outside the tent. You can see the single return at the bottom of the box. The red thing on top of the pump is the reducer Like a said, id do a double return next time, but you get the idea. If you look at the pic above, then this one, its like, inside the tent- outside the tent Here is my 4 pot system in action with spraybars (the spray bars are a different design, but the principle is the same). On the subject of dissolved oxygen, you can also add an airstone or 2 to this system. You don't really NEED to, but they help by creating yet more oxygen to the rootzone, like I did in the above system. so that's the spray bars and returns done, you are nearly there. For the net pots you need to make some holes in the lids. I use 200mm net pots, and to make the hole I devised a cunning plan, baldrick would be proud of. here is how its done. Mark the centre of the box lid, drill very small pilot hole, then get a piece of timber, and put a drywall screw through one end, so the tip of the screw ids protruding by about 3-5mm. then measure out 95mm and put another screw through the same amount. Put one screw in the pilot hole you drilled, and then turn the wood through 360 degrees scoring a perfect circle into the plastic. Then you just keep on scoring round and round till you eventually go through the lid , or it gets so thin you can cut it with a Stanley. Also when this is done insulate the boxes if possible, ive used Kingspan in the top pics, or even the silver reflective bubble wrap stuff for the lids is better than nothing, DO it. chillers - you WILL need one Chillers have a separate pump- a maxijet 1000l/hr job from the res to the chiller, and the warer will naturally return from the chiller to the res, , if you can try and get the return to make the water fall back to the res - more DO - you know it makes sense. Pop in your net pot, fill with hydroton and grow big fuck of trees. My first run in the 2 pot system produced 700grams from two (whisper it ) autos Mission accomplished. If I think of anything else I will add it. Mon the water
badbillybob posted a topic in Sweet Seeds Competition Grow Diaries 2019/20Hello and welcome to my competition diary.. I have decided to enter this competition as I have a few strains from sweet seeds that have been gnawing away at my sub conscious- go on Billy,..... try them …...it says, you know you want to.....and I do...….so I am...... strains in question are a few of Sweet seeds best performers. I have chosen Black jack, cream caramel and Sweet afghan delicious s1, all of which I have wanted to do for a good while, but never got round to. Heres the contenders, limbering up in the background Black Jack Crossbreed of our Black Domina with an exceptional Jack Herer that features a pleasant and intense bouquet similar to the Haze’s cathedral incense aromatic trait. The result is Black Jack® (SWS01), one of our most powerful and productive strains.This classic strain features great hybrid vigor and it is totally adapted to indoor grows. When planted outdoors, directly in the ground and with enough sunlight, it becomes a resinous hairy monster of about three meters of height.Indica/Sativa: 50%/50%THC: 16-21% · CBD: 1,0%Indoor Yield: 500-600 g/m2Indoor Blooming: 9 weeks Cream caramel This synthetic strain is the result of a three way cross between our best Indicas: Blue Black x Maple Leaf Indica x White Rhino.This classic strain features a sweet intense taste that is reminiscent of caramel, combined with a hint of earthy flavors inherited from the Blue genetic that intervenes in the cross. This strain is ideal for indoor growing.This strain is the favorite of medicinal cannabis users. Relaxing and antidepressant. Indica/ Sativa: 90%/10%THC: 15-20% · CBD: 1,6%Indoor Yield: 400-550 g/m2Indoor Blooming: 8-9 weeks Sweet Afghan Delicious s1 Self-pollination of one of our most powerful and aromatic mothers, a Black Domina selected in 1998.The self-pollination of this super mother produces dense buds covered by abundant resin. This strain features sweet intense aroma and a musky flavor inherited from its afghan ancestors.This S1 seed allows for a very homogeneous offspring regarding the described characteristics. Easy to grow and very resistant to pests and fungus. Indica/Sativa: 90%/10%THC: 15-20% · CBD: 1,8%Indoor Yield: 400-500 g/m2Indoor Blooming: 8-9 weeks And so to the plan . The plan is to wet 2 of each strain and hope hey all sprout nicely for me. I will play them music and sing sweet melodies to them to increase my chances. For those of you who have been fortunate enough to miss my previous ramblings, my system of growing is HYDRO, using a home made RDWC system with top fed spray bars and airstones. Its been developed by myself over the years and is working pretty well now, altho, as with most things, it could be improved. Here it is. I wont bore you to tears with the lowdown on it, but will condense it to say the totes are 60 litres, the net pots 250mm, the airpumps are 60litres, 2 golf ball airstones per pot, chiller is hc300 hailea, and the water pumps are 4000litre for the 4 pot side and 8000 litre for the 5 pot side. Nutrient line is Ionic, used for years and good enough for Heath Robinson (my hero...………...swoon....lol)…... im actually repairing a leak on it today, or at least that was the plan, but the section I cut out, I tested it and no leaks, so I just put it back, with new joint connectors. I will leave the glue to set and trial fill it tonight, with everything crossed. So once the system is cleaned and leak free, we will wet some beans . Can you feel the excitement? I can...…………. So take a seat, skin up a fat one, and hold on for the ride...….